19%OFF
  • DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission
  • DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission
  • DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission
  • DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission
  • DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission
  • DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission

DOITING Remote Control Wireless Wifi Module ESP-M2 ESP8285 Module Compatible With ESP8266 Transparent Transmission

0 stars, based on 0reviews
Price:
$2.10$1.71 / piece
Color
  • AT firmware
  • TT firmware
Quantity: - + 1000items available

Item specifics

Model Number:
ESP-M2
Product Type:
Oral Irrigator Parts

Shipping list:

  • AT firmware= 1pcs AT firmware module
  • TTfirmware= 1pcs Transparent transfer firmware module

Features:

  • Ultra-small size;
  • Serial to WiFi;
  • Wireless transparent transmission;
  • Long distance ultra low power consumption;
  • An external antenna can be used.
  • High temperature resistance up to 125°C
  • Fully compatible with ESP8266, the source code can be directly ported.
  • The ESP-M2 module core processor uses the cost-effective chip ESP8285. The chip integrates an enhanced version of Tensilica's L106 Diamond Series 32-bit core processor in a smaller package with on-chip SRAM. The ESP8285 has a full Wi-Fi network function, which can be used independently or as a slave to other host MCUs. When the ESP8285 hosts an application, it can be launched directly from external Flash. The built-in cache helps improve system performance and optimizes the storage system. In addition, the ESP8285 can be used as a Wi-Fi adapter via the SPI/SDIO interface or I2C/UART port, and can be applied to any microcontroller-based design.

Parameters:

SOC characteristics:

  • Built-in Tensilica L106 ultra-low power 32-bit microprocessor with 80MHz and 160MHz frequency support, RTOS support
  • Built-in TCP/IP protocol stack
  • Built-in 1 10 bit high precision ADC
  • Peripheral interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
  • Deep sleep keeps current at 10uA and shutdown current is less than 5uA
  • Wake up, connect and pass packets within 2 ms
  • Standby power consumption is less than 1.0mW (DTIM3)
  • Built-in 1Mbyte SPI Flash

Wi-Fi features:

  • Support for 802.11 b/g/n/e/i
  • Support Station, SoftAP, SoftAP+STA mode
  • Support for Wi-Fi Direct (P2P)
  • Supports hardware acceleration of CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC
  • P2P discovery, P2P GO mode/GC mode and P2P power management
  • WPA/PA2 PSK and WPS
  • 802.11 i security features: pre-authentication and TSN
  • Support for 802.11n (2.4 GHz)
  • 802.1h/RFC1042 frame packing
  • Seamless roaming support
  • Support AT remote upgrade and cloud OTA upgrade
  • Support for Smart Config (including Android and iOS devices)

Module peripherals:

  • 2xUART
  • 1xADC
  • 1xEn
  • 1x wake-up pin
  • 1xHSPI
  • 1xI2C
  • 1xI2S
  • Up to 10xGPIOs
  • Operating temperature range: -40°C-125°C
  • Module size: 12.3mm × 20mm

ESP8285模块管脚Q612

Application scenario:

  • Household appliances
  • Home automation
  • Smart socket, smart light
  • Mesh network
  • Baby monitor
  • IP camera
  • Sensor Networks
  • Wearable electronics
  • Security ID tag
  • Wireless location awareness
  • Wireless positioning system beacon
  • Industrial wireless control

Note:

  • The module supply voltage is 3.3V DC and the current is 500mA or more;
  • Wi-Fi module IO maximum output current is 12mA;
  • Wi-Fi module NRST pin is active low; EN enable pin is active high;
  • The Wi-Fi module enters the upgrade mode: GPIO0 is at a low level, then the module is reset and powered on; the Wi-Fi module enters the normal working mode: GPIO0 is at a high level, and the module is reset and powered.
  • The RXD of the Wi-Fi module is connected to the TXD of the external MCU, and the TXD of the Wi-Fi module is connected to the RXD of the external MCU.
  • More documents can be downloaded at wiki.doit.am.

Q1Q2Q4Q5

 

 

Hot Sales

    Recent Reviews
    +