ESP8266 ESP-F Wireless WiFi Module AT/ Transparent Transmission/ MQTT Firmware Serial WiFi Compatible With ESP-12E/ ESP-12F

0 stars, based on 0reviews
Price:
$26.80$22.80 / piece
Color
  • TT firmware
  • MQTT firmware
  • AT firmware
Quantity: - + 10000items available
Inquiry Now

Item specifics

Brand Name:
SZDoit
Material:
Composite Material
Tool Supplies:
Tools
Upgrade Parts/Accessories:
Adapter
RC Parts & Accs:
Receivers
Size:
16mm*24mm
Use:
Vehicles & Remote Control Toys
Technical parameters:
Value 5
Model Number:
ESP-F
Remote Control Peripherals/Devices:
Receivers
For Vehicle Type:
Cars
Four-wheel Drive Attributes:
Assemblage
Wheelbase:
Bottom Plate
Description

Option description:

  • AT firmware: refers to the module with AT firmware, this firmware only supports AT instructions to operate the module;
  • TT firmware: refers to the module with transparent transmission firmware, this firmware configures the module through the web page, similar to router configuration;
  • MQTT firmware: refers to the module with MQTT firmware.

Shipping list:

  • 10 piece ESP-F module (optional)

Product introduction:

  • The core processor of the ESP-F module uses the cost-effective chip ESP8266EX. This chip integrates the industry-leading Tensilica ’s L106 ultra-low-power 32-bit micro MCU in a smaller package, with a 16-bit reduced mode, the main frequency supports 80 MHz and 160 MHz, and supports RTOS. ESP8266EX has a complete Wi-Fi network function, which can be used independently or run as a slave on other host MCUs. When the ESP8266EX is used independently, it can be started directly from the external flash. The built-in cache memory helps improve system performance and optimizes the storage system. In addition, ESP8266EX can be used as a Wi-Fi adapter through SPI / SDIO interface or I2C / UART port, and can be applied to any microcontroller-based design.
  • ESP-F module supports standard IEEE802.11 b / g / n / e / i protocol and complete TCP / IP protocol stack. Users can use this module to add networking capabilities to existing equipment or build stand-alone network controllers.
  • The ESP-F module provides maximum practicality at the lowest cost, providing unlimited possibilities for Wi-Fi functionality to be embedded in other systems.

ESP8266模脚

Features:
SOC characteristics:

  • Built-in Tensilica L106 ultra-low-power 32-bit microprocessor, the main frequency supports 80MHz and 160MHz, supports RTOS
  • Built-in TCP / IP protocol stack
  • Built-in 10-bit high-precision ADC
  • Peripheral interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
  • Deep sleep holding current is 10uA, shutdown current is less than 5uA
  • Wake up, connect and deliver packets within 2 ms
  • Standby power consumption is less than 1.0mW (DTIM3)

Wi-Fi characteristics:

  • Supports 802.11 b / g / n / e / i
  • Support Station, SoftAP, SoftAP STA mode
  • Support Wi-Fi Direct (P2P)
  • Supports CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC hardware acceleration
  • P2P discovery, P2P GO mode / GC mode and P2P power management
  • WPA / PA2 PSK and WPS
  • 802.11 i security features: pre-authentication and TSN
  • Supports 802.11n (2.4 GHz)
  • 802.1h / RFC1042 frame encapsulation
  • Seamless roaming support
  • Support AT remote upgrade and cloud OTA upgrade
  • Support Smart Config function (including Android and iOS devices)

Module peripherals:

  • 2xUART
  • 1xADC
  • 1xEn
  • 1x wake-up pin
  • 1xHSPI
  • 1xI2C
  • 1xI2S
  • Up to 11xGPIOs
  • 4M bytes SPI Flash
  • Operating temperature range: -40 ℃ -85 ℃
  • Module size: 16mm × 24mm

78

Application scenario:

  • Household appliances
  • Smart home
  • Baby monitor
  • Sensor Networks
  • Security ID tag
  • Wireless positioning system beacons
  • Home automation
  • Mesh network
  • IP Camera
  • Wearable electronics
  • Wireless location awareness
  • Industrial wireless control

Note:

  • The module supply voltage is 3.3V DC and the current is 500mA or more;
  • Wi-Fi module IO maximum output current is 12mA;
  • Wi-Fi module NRST pin is active low; EN enable pin is active high;
  • The Wi-Fi module enters the upgrade mode: GPIO0 is at a low level, then the module is reset and powered on; the Wi-Fi module enters the normal working mode: GPIO0 is at a high level, and the module is reset and powered.
  • The RXD of the Wi-Fi module is connected to the TXD of the external MCU, and the TXD of the Wi-Fi module is connected to the RXD of the external MCU.

910

 

 

Hot Sales

    Recent Reviews
    +